LOADING 3D MODEL…
VTM Academy
Inside the
Vertical Tote Mover.
A tall, slim robot that drives along the rack aisle, lifts an orange carriage up its mast and fills eight onboard buffer shelves, so one trip moves several totes.
- Storage height
- Up to 33 ft
- Max payload (VTM)
- 300 kg / 660 lb
- Throughput per bot
- 35 in + 35 out totes / h
- Buffer slots
- 8
- Illustrative (concept model)
Scroll story
One VTM trip
Six steps, from task to station. Parts in use glow on the robot and the signal path shows below it.
STEP 01
Drive to the rack column
The task arrives over Wi-Fi. The robot computer plans the move and the controller drives the base along the aisle until it lines up with the right rack column.
STEP 02
Raise the carriage to level 6
The lift driver feeds current to the lift motor; the carriage climbs the mast. The lift encoder and an independent position sensor confirm it stopped at exactly the right height.
STEP 03
Reach in and pull the tote
The fork extends into the rack, grips the tote and pulls it onto the carriage. The fork sensor confirms both end positions before anything else moves.
STEP 04
Store it on a buffer shelf
The carriage turns to the robot's own shelves, drops to a free slot and pushes the tote off. One robot can carry several totes per trip.
STEP 05
Repeat for three more totes
Same loop, different levels: rack level 4, 2 and 8 go to buffer slots 2, 3 and 4. The shelves fill one by one.
STEP 06
Drive to the station drop and unload
The robot drives to the end of the aisle and hands the totes to the station conveyor one by one, emptying its buffer for the next trip.
Exploded view
Take it apart.
Keep scrolling: the base opens, the electronics lift out, the mast separates and the shelves fan out. Tap a label to learn what that part does. Layout is illustrative.
Component
Carriage
- What it is
- The part that travels up and down holding the fork.
- What it does
- Brings the fork to the right storage level.
- Input
- Transmission force
- Output
- Vertical position
- Communicates with
- Lift transmissionSensors
Drive-it lab
Drive it.
A training simulation, not a real control panel. Move the carriage, work the fork and buffer, then inject a fault.
Scale
How tall is it?
Tote-to-person storage reaches up to 33 ft, and the VTM's mast reaches the top level. Next to a person, that's roughly six times their height.
Rack height: Up to 33 ft (Ranger TTP). Person (1.75 m) and robot drawing are illustrative.
Source: GreyOrange — Tote-to-Person (opens in a new tab)LOADING 3D MODEL…
XRAY · CONCEPTUAL LAYOUT
01 · Explore
From the outside in.
Switch views to strip away the shell, separate assemblies, or see only the electrical, network, software or sensor systems. Component placement is illustrative.
- Network / data
- Software / control
- Electrical / motion
- Sensor feedback / healthy
- Fault / safety
Components
Component
Lift motor
- What it is
- Converts electrical energy into mechanical movement.
- What it does
- Raises and lowers the carriage.
- Input
- Current from the driver
- Output
- Torque / rotation
- Communicates with
- DriverEncoderController
02 · Command to motion
Command to motion
Storage retrieval requested. Follow the command from the warehouse system, across the network and Wi-Fi, into the robot computer, through the controller and driver to the lift motor — then watch the sensors confirm it and the status travel back.
COMMAND → DECISION → COMMUNICATION → CONTROL → ELECTRICAL ENERGY → MOTION → SENSOR FEEDBACK → STATE UPDATE
Storage retrieval requested
- OrchestrationSOFTWARE
- Fleet / equipment schedulingSOFTWARE
- Robot interface / middlewareSOFTWARE
- NetworkNETWORK
- Access pointNETWORK
- Robot wireless clientNETWORK
- Robot computerSOFTWARE
- Safety & interlocksCONTROL
- Embedded motion controllerCONTROL
- Lift motor driverELECTRICAL
- Lift motorELECTRICAL
- Lift mechanismELECTRICAL
↑ FEEDBACK RETURNS
EncoderSENSOR- Position sensorSENSOR
- Embedded controllerCONTROL
- Robot softwareSOFTWARE
- MiddlewareNETWORK
- OrchestrationSOFTWARE
03 · Manual-control lab
What does “Lift up” actually mean?
TRAINING SIMULATION — actual controls vary by robot model, software release and site safety configuration. No real credentials, addresses or production interfaces are represented.
- LIFT
- 15%
- FORK
- HOME
- SAFETY
- OK
- CONTROLLER
- READY
Press a control to slow time down and see each step.
04 · Motors & drivers
Requested versus actual.
The controller sends a motion instruction. The driver decides how much electrical current the motor needs. The motor moves; the encoder reports what really happened. If requested and actual differ beyond acceptable limits, the axis faults. Inject a fault to see where the loop breaks.
Requested vs actual position
- - requested— actual (encoder)
HEALTHY
Typical symptom · Actual follows requested closely. No fault.
Check · —
INTERNAL / AUTHORIZED ONLY
Drive parameter configuration and tuning values — available only in the model-specific, authorized SOP for your site. Not published on this website.
05 · SOPs
Go from understanding to procedure.
- VTM lift systemHow the lift axis moves the carriage between storage levels and confirms position.
- VTM fork / tote handlingHow the fork transfers totes and which interlocks must be satisfied first.
- Motor / servo driversHow drivers turn controller commands into motor power — and how requested vs actual becomes a fault.
- E-stop & safety stateWhy a robot with a valid command still won't move when the safety chain is open.
- Battery & chargingPower state, charging behaviour and how low power affects task acceptance.
- Industrial WLAN client diagnosticsRead association, BSSID, channel and RSSI to judge wireless health on a moving robot.